Armattan OOmph 2206/2300 KV Motor *Out of stock

US$20.50
Write a Review
Armattan OOmph 2206/2300 KV Motor *Out of stock

armattan-oomph-motor-bolts-washers.jpg

Motor Specifications

Stator Diameter

 22mm                    

Stator Height

 6mm 

 KV (rpm/Volt)

 2300

Weight

 31g with full wires      

Recommended Props

 5 or 6 inch

LiPo Compatibility

 3-4S

Prop Mount Height

 5mm

Prop Mount Diameter

 5mm

Interior Threading 

  CW or CCW

Magnets

 N52H arc magnets

Stator Laminations

 0.15mm

Winding

 Single Wire

Bearing

 Genuine NMB

Johnny FPV - Flying Armattan OOmph motors 

Armattan oomph-logo-stator-kv-.png

 
Important Note: We HIGHLY recommend that you purchase motors threaded in both directions. Prop strikes where bolt threads match rotation can lead to loosened and lost mounting hardware.  Now...on with our regularly scheduled programming.
armattan-oomph-2206-motor-with-prop-4a-.jpg

Did you ever wish your bird just had a little extra something to give, but didn't want to break your batteries (and the bank)?  If so, Armattan's OOmph motors are the choice for you.  Designed and produced with the finest quality materials, these brushless beasts will provide an unmatched thrust/amp ratio among 2206 sized motors.  If you don't believe it, just check out Ryan Harrell's review over at Miniquad Test Bench.

This motor packs much of your standard fare; an M3/22xx mounting pattern, a screw that secures a hollow shaft, and genuine NMB bearings, for some.  What may stand out the most, however, is the unique prop-fastening adapter on top.  Why this design?  After rigorous testing (read: lots of crashes) it was observed that standard exterior-threaded shafts can be heavy, can bind on props, and require large hardware to remove (who wants to carry around a socket wrench?).  This is why the OOmph motors were conceived with a better solution.

A New Approach

With Armattan's innovative design changing props is easy. All that holds the propeller down is a standard M3 bolt and washer combination on the top of the motor. Once the bolt is unscrewed, the propeller and washer will slide right off of the smooth shaft. Gone are the days of fighting to pull off a blade-less hub and coming away bruised and bloodied. Besides eliminating binding, the OOmph motors have a shorter (lighter) shaft and require only a hex-key (Allen Wrench) for a prop-swap.  Another added feature of this solution is that the bolts are threaded opposite of the rotation direction. Since we don't yet have nylock bolts, this causes any impact to the prop to tighten the prop instead of unscrewing it.

A final feature, though perhaps the least functional, is that the aluminum was anodized in the same house that is providing the aluminum hardware for the Chameleon frame. These components will be the exact same shade of orange. That's good news for those who like to coordinate their builds.

Are these not what you're looking for?  If you'd be better fulfilled by something that spins a bit quicker, check out our silver OOmph 2205/2550kv motors.  For the micro lovers among us, take a look at the strikingly purple 1407/3850kv version.

Special Thanksoomph-315x600.jpg

A massive thank you goes out to Andrew Meyer and Matt Denham. Andrew, based in Canada, had the novel idea to reverse threading on a motor shaft. For a long time, this was not really possible because most motors were using aluminum propeller adapters. Not that long ago, however, many motor manufacturers began using hollow stainless steel shafts as propeller adapters instead of alumi. The idea, as elusive or as obvious as it may be, is to utilize the stainless steel shaft in a smarter, lighter, stronger, and lower profile application. Simple, but brilliant.

Matt Denham, based in the UK, designed the motor top. We wanted no frills. We knew that by using a shorter shaft we were dropping weight and we used this weight to complement a sturdy motor top. Matt's work alongside Andrew's originality and the latest racing motor technology sees results that exceed our expectations. This results with a product that is light and tough, with a unique prop mounting system, power on demand, and the most efficient 2206 motor on the market today. Oomph!

Included 

2x Motors with wires (1 CW, 1 CCW)
12x M3 bolts for propeller and mount (2 extra)
4x prop-washers (2x extra)

Important Note: CW and CCW engraving on the motors refer to motor rotation, not thread rotation.